Loadbearing capacity of infill masonry walls considering the deformation‐based membrane effect

According to currently valid codes, it is not possible to determine the loadbearing capacity of unreinforced infill walls considering the deformation‐based membrane effect by incorporating the exact support conditions. One reason for this is the lack of a validated calculation procedure, which in addition to the equilibrium conditions also realistically represents the compatibility conditions of these systems. In the present paper, therefore, a new non‐linear analytical calculation procedure is presented. The main focus of the analysis of walls subject to area loading is the incorporation of the support conditions and thus the consideration of the deformation‐based membrane compressive force. Through generalised formulation and a standardised notation of the determination equations, different material behaviours and various support conditions can be taken into account with few parameters. On the action side, both lighter loading like wind loads and heavier loading like explosion loads can be considered. Through the implementation of the partial factor concept, it is possible to comply with the requirements of European codes and thus ensure the applicability of the analysis model.     

载荷影响下的机电阻抗协整结构损伤识别方法

高频机电阻抗(electromechanical impedance, 简称EMI)方法利用粘贴在结构表面的压电传感器(piezoelectric transducer, 简称PZT)进行主动激励，通过连续监测和分析PZT机电导纳信号的变化评估结构的健康状态；然而EMI方法容易受到环境工况变化的影响，导致结构损伤的误报。针对此问题，采用时间序列协整方法处理及消除结构工作载荷对阻抗谱特征信号的影响。该方法是基于结构动荷载作用下PZT阻抗谱导纳信号的非平稳特征，将动荷载影响下的阻抗谱非平稳时间序列经线性组合变换成平稳时间序列，根据得到的协整余量序列有效判断结构的健康状态。为验证该方法的有效性，开展了动应力影响下铝梁结构的螺栓松动损伤识别实验。结果表明，协整消除了动态应力对EMI方法的影响，当铝梁内存在持续变化的应力时，仍可以准确识别螺栓松动。机电阻抗协整方法能够消除结构健康监测中荷载作用的影响，及时准确地进行结构损伤识别。     

25CrNi2MoV钢的微动磨损性能

采用微动摩擦磨损试验机在干摩擦条件下对新型高速重载传动轴用25CrNi2MoV钢进行微动磨损试验,研究了不同载荷(50~200N)和频率(15~30Hz)下该钢的微动磨损性能。结果表明:在频率为20Hz条件下,当载荷由50N增至200N时,25CrNi2MoV钢的平均摩擦因数由0.766减至0.661,磨损体积由19.65×10^-3 mm^3增至75.83×10^-3 mm^3;在载荷为30N条件下,当频率由15Hz增至30Hz时,平均摩擦因数由0.790增至0.905,磨损体积由11.43×10^-3 mm^3增至23.88×10^-3 mm^3;在不同试验参数下,25CrNi2MoV钢磨损表面均出现了氧化和犁沟现象,磨损机制包含氧化磨损和磨粒磨损;在频率为20Hz条件下,载荷为50,100N时,25CrNi2MoV钢的磨损机制以黏着磨损为主,载荷为150,200N时,主要磨损机制为疲劳磨损;在载荷为30N条件下,频率为15~25Hz时,磨损机制以磨粒磨损为主,当频率增至30Hz时,磨损机制以疲劳磨损为主。     

海绵负载纳米Al2O3复合吸附剂去除水中硒研究

研究制备了海绵负载纳米Al2O3微球的复合吸附剂(NAS),并用于对Se(Ⅳ)和Se(Ⅵ)的吸附。结果表明,合成的纳米Al2O3微球(NAO)的平均尺寸为200~400 nm,在海绵上负载NAO会使其分散性更好。当NAO负载量分别为80 mg/g和60 mg/g时,NAS对Se(Ⅳ)和Se(Ⅵ)的吸附性能为佳,分别需要60、120 min达到平衡,适应pH为2~5;两者均符合准2级动力学模型;NAS对Se(Ⅳ)、Se(Ⅵ)的最大吸附容量分别为137.2、143.9 mg/g,能很好地与Freundlich模型拟合,说明NAS表面不均匀,且属于多层吸附。经过2次的循环,对Se(Ⅳ)和Se(Ⅵ)的去除率有所降低,但均仍保持在一定的水平,说明NAS可再生循环利用。NAS作为一种新型吸附剂去除水中Se具有较好的应用前景。     

船体结构冰载荷反演方法及试验验证

冰载荷是影响船舶冰区航行期间结构安全的重要环境载荷。船舶的冰压监测通常采用应变传感器，合理地布放传感器是识别冰载荷的基础。通过对比船体外板结构试验中的冲击载荷和不同测试方案下的应变信号，确定了最佳应变传感器布放方案；采用Green核函数方法建立了船体外板结构应变冲击载荷间的响应关系，并对采集信号在噪声影响下反演的不适定性进行了分析；采用Tikhonov正则化方法克服了载荷反演过程中出现的数值不稳定问题；最后将试验中的响应用到载荷识别分析中，反演的载荷可以较为准确地反映冲击载荷的时域特征并且载荷识别精度良好。     

泛在电力物联网在北京经济技术开发区的应用探索

泛在电力物联网是物联网在电力领域的具体体现，建设泛在电力物联网是推进"三型两网"建设的关键环节，也是实现能源转型的必要手段。阐述了泛在电力物联网的定义，从供电公司角度出发，根据北京经济技术开发区实际情况，讨论了依托地区特点的泛在电力物联网实施策略和实际应用场景，分析了可能遇到的问题。得出结论：随着泛在电力物联网的深入建设，供电公司能够为电力客户提供多元化服务，提高客户满意度；地市供电公司能够依托泛在电力物联网开展更多电力相关业务；泛在电力物联网的安全性、实用性、有效性是发展面临的首要问题。     

Wet abrasive wear behavior of WC-based cermet coatings prepared by HVOF spraying

In this study, three kinds of WC-based cermet coatings including WC–CoCr coating, WC–Ni coating and WC–Cr₃C₂–Ni coating were prepared by the high-velocity oxygen-fuel (HVOF) spraying process. Scanning electron microscopy (SEM), energy disperse spectroscopy (EDS) and Vickers hardness tester were used to analyze the microstructure and mechanical properties of these coatings. The WC–CoCr coating presented the highest average microhardness of 1205 HV_0.3, and then followed by the WC–Cr₃C₂–Ni coating (1188 HV_0.3) and the WC–Ni coating (1105 HV_0.3). The abrasive wear behavior of the WC-based coatings under the conditions of different applied loads and sediment concentrations were studied by a wet sand-rubber wheel tester. The results indicated that the abrasive wear loss rates of all the coatings increased with the increment of applied load or sediment concentration. In addition, the coatings with higher microhardness appeared to have higher abrasive wear resistance. The abrasive wear resistance of the WC-based coatings was 4–90 times higher than that of AISI 304 stainless steel under the same testing condition. The abrasive wear mechanism of the WC-based coatings was deduced to be the extrusion and removal of binder phases, as well as the fragmentation and peel-off of hard phases.     

循环水替代7℃水在氯乙烯精馏装置中的应用研究

详细计算了PVC生产精馏系统换热设备的热负荷、循环水量及运行成本,认为通过调整系统的运行温度和压力,精馏装置使用循环水替代7℃水具有可行性,这将有利于突破能耗高的技术瓶颈,最大程度地发挥节能降耗、减污增效的潜能。     

Enhancing stability region of time‐delayed smart power grids by non‐integer controllers

In this study, the impacts of non‐integer order controller on the stable parameter space of the microgrid (MG) frequency control system with fixed communication time delay are investigated and discussed with the help of the stability boundary locus (SBL) method. This study proposes a non‐integer order controller for the load frequency control (LFC) of the MG systems. To that end, the load frequency model of the MG is formulated and then the characteristic equations of this model are obtained. Then, with the help of this characteristic equation, the stable parameter space of the non‐integer controller is determined with regard to different time delay (τ ) and fractional integral order values (α ) using the SBL method. In order to show the accuracy of the obtained stable parameter space, time domain and generalized modified Mikhailov (GMM) criterion studies are carried out for different values of (τ ) and (α ). According to the results obtained, the areas of stable parameter space according to different α values and τ = 1.6 are calculated as 444.8860 for α = 0.4 , 342.9728 for α = 0.7 , 259.3578 for α = 1 , 216.2541 for α = 1.3 and 159.6826 for α = 1.6 . In addition, the areas of stable parameter space according to different τ values and α = 1.4 are calculated as 784.5222 for τ = 1 , 106.3219 for τ = 2 , 29.6959 for τ = 3 and 11.5946 for τ = 4 . Despite the extreme variability arising from nature of resources that make up the MG, the designed non integer order controller with the values selected within the stable parameter space stably carries out LFC control of the MG.